Input Frequency Range 2400-2490 MHz

Output Frequency Range 5725-5850 MHz
Operating Mode Bi-directional TDD
LO Frequency & Frequency Stability 3360 MHz; ± 2.0 ppm
Output Power 200 mW (23 dBm)
Transmit Input Power Min: 1.6 mW Max: 30 mW
Receive Input Power 0.1 mW (-10 dBm)
Receive Gain 23 dB Typical
Frequency Response Flatness ± 1dB over operating range
Noise Figure 4 dB
Switching Time < 1 µs
Connectors N-Female
Operating Temperature -22°F to 140° (-30°C to 60°C)
Power Consumption 12VDC, 1.5A
LED Indication Transmit: Green; Receive: Red
Dimensions (LxWxH) 7.6 x 3.7 x 0.9 (195 x 95 x 23 mm)
Weight 1.5 lbs. (720 g)

● 200mW high performance bi-directional frequency up/down converter that converts 2.4 GHz wireless equipment to the less crowded 5.8 GHz frequency band. Its rugged weatherproof design allows outdoor installation using the included mounting kit. The converter's remote-mounted design maximizes operating range by delivering full transmit power and low-noise receive gain directly at the antenna where it is most effective. This converter is compatible with 2.4 GHz radio devices including IEEE 802.11b/g and most half-duplex Spread Spectrum data radios. Included is a DC Power Injector which provides power to the unit through the antenna cable, 12V power supply and mounting hardware.      ►Lead time 1 week

►Typical Characteristics:
 Effective Gain Frequency band  2.4 - 2.5 GHz

 Supply voltage

12 Volt unregulated

 ● Receiving direction:

 Gain

20±2dB over temperature range

 Noise figure

4.5 dB

 Linear operation

Pin < -18 dB

 Tx/Rx Transition time

  ≤ 4 μSec

 IP³ input

13 dB

 ● Transmitting direction:

 Gain

17 dB

 P1dB compression point

29 dB

 RF input threshold for switch to transmission

 > 1dBm

 Rx/Tx transition time

≤ 2 μSec

 ● Low cost and miniature size

 ● High dynamic range

 ● 29 dBm P1dB compression point

 ● 3-pole ceramic bandpass Chebyshev filter.

 ● Low noise figure

 ● Tx-Red / Rx-Green LED indication

 ● Lightning protection: 1/4λ Shorted strip line.

 ►Lead time 1 week

 ● Temperature range -40 +70 C°

 ● Dimensions ≈ 80x50x12.5mm, 3"x2"x0.5"

 ● SMA-F connectors

 ● Weight 120 g

 ● Supplied with coax. 50 Ohm DC isolated power injector and AC-DC power supply

 ● Output power never exceed 800 mW, so, to meet FCC Rules, calculate EIRP considering this parameter.

 ● Example (unreal cable losses) :

Cable Losses=-10 dB(20m of LMR200) connector losses=-1.5 dB, AP output=17 dBm. Pin= 17-1.5-10=5.5 dBm. Therefore, Pout = 5.5dBm +17dB = 22.5dBm or 180 mW.

F,MHz/Type LMR-100A LMR-195 LMR-200 LMR-240 LMR-300 LMR-400 LMR-500A Times Microwave Systems classification table
30 MHz 12.9 6.5 5.8 4.4 3.5 2.2 1.8 LMR-100, RG-316, RG-174 Ø2.79mm
50MHz 16.7 8.4 7.5 5.7 4.5 2.9 2.3 LMR-195, LMR-200, RG-58, RG-142 Ø4.9mm
150MHz 29.4 14.6 13.1 9.9 7.9 5.0 4.0 LMR-240, Ø 6.1mm
220MHz 35.8 17.7 15.9 12.0 9.6 6.1 4.9 LMR-300, Ø 7.62mm,  LMR-500A, Ø12.7mm
450MHz 51.9 25.5 22.8 17.3 13.8 8.9 7.1 LMR-400, RG-8, RG-213. Ø10.29mm
900MHz 74.9 36.5 32.6 24.8 19.9 12.8 10.3

1500MHz 98.7 47.7 42.4 32.4 26.0 16.8 13.6
1800MHz 109.0 52.5 46.6 35.6 28.7 18.6 15.0
2000MHz 115.5 55.4 49.3 37.7 30.3 19.6 15.9
2500MHz 130.6 62.4 55.4 42.4 34.2 22.2 18.0
5800MHz 210.3 98.1 86.5 66.8 54.3 35.5 29.1